Fluke 789/773

Bundle Highlights

• Measure 4-20 mA signals without breaking the loop with the 773 mA ClampMeter. Also, source or measure 4-20 mA and 1-5 or 0-10 V dc signals to test analog I/O
• Measure any analog process or automation signal and source mA signals with the 789 ProcessMeter
• Measure inputs and outputs of motors and drives safely with the CAT IV 600V rated 789 ProcessMeter

>

Fluke 789 Features

• 24 V loop power supply
• HART mode setting with loop power (adds 250 ohm resistor)
• 100% larger dual display
• 1200 ohm drive capability on mA source
• Enhanced backlight with two brightness settings
• Improved battery power with four AA batteries
• 0-100% mA Span Check buttons to toggle between 4 and 20 mA
• Infrared I/O serial port compatible with FlukeView Forms
• V 2.1 Software (available Feb. 2003)
• 5 V dc measurement capability on the 4 V dc range for precise 1-5 V measurements
• Externally accessible fuses for easy replacement
• DMM designed to meet 1000 V IEC 1010 Cat III standards
• Precision 1000 V, 440 mA digital multimeter
• Measure ac and dc volts
• AC and dc voltage accuracy: 0.05 % dc current accuracy, 1 uA resolution to 30 mA
• Simultaneous mA and % of scale readout
• True-rms ac voltage measurement
• Frequency measurement to 20 kHz
• Min/Max/Average/Hold/Relative modes
• Diode Test and Continuity Beeper
• 20 mA dc current source / loop calibrator / simulator
• Simultaneous mA and % of scale readout
• Manual Step (100 %, 25 %, Coarse, Fine) plus Auto Step and Auto Ramp
• Externally accessible battery for easy battery changes V overload protection on V, ohms, frequency, mA (backed-up by 440 mA 1000 V fuse)
• Process Meter

>

Fluke 789 Includes

• TL71 Premium Test Lead Set
• AC72 Alligator Clips
• Four AA alkaline batteries (installed)
• Users Manual
• Quick Reference Guide

>

If you need more time in your busy day take a good look at the Fluke 773 mA Clamp Meters. It’s designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system.

Fluke 733 Features

• Best in class 0.2 % accuracy
• 0.01 mA resolution and sensitivity
• Measure 4 to 20 mA signals without ”breaking the loop”
• Measure mA signals for PLC and control system analog I/O
• Dual backlit display with both mA measurement and percent of 4 to 20 mA span
• Measurement Spotlight illuminates hard to see wires in dark enclosures
• Detachable clamp with extension cable for measurements in tight locations
• Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
• Automatically change the 4 to 20 mA output for remote testing
• Power saving features, auto-off, backlight timeout extend battery life
• Hold function captures and displays changing measurements
• Measure 4 to 20 mA signals with in-circuit measurement
• Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
• Source 4 to 20 mA signals for testing control system I/O or I/Ps
• mA output linear ramp or 25% step output
• DC voltage measurement to verify 24V power supplies or voltage I/O signals
• Source DC voltage to test input devices that accept a 1-5V or 0 to 10V signals
• Scaled mA output provides a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp
• mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal
• Voltage output linear ramp or 25% step output

>

Fluke 733 Includes

• Four AA alkaline batteries (installed)
• Soft carrying case
• TL75 test leads
• AC 72 detachable clip
• TL 940 mini hook test leads
• Instruction sheet
• Hanging tool with hook and loop strap